speed calculation

Subject: speed calculation May 12th 2013, 9:24 pm

Speed Calculation Sheet

Engine RPM:
Gear Ratio:
Tire Size (Rear):

Wheel Circumference - Wheel Diameter X 3.14=

Circumference In Feet - wheel circumference /12=

Wheel RPM - Engine RPM / Gear Ratio =

Feet / Min. - Wheel Circumference(ft) X wheel rpm =

Feet / Hr. - feet per min X 60=

Miles / Hr. - /5,280 = mph

Subject: Re: speed calculation May 12th 2013, 11:37 pm

Thank you for posting this. Also, if this forum is capable of hosting the file and if anybody is interested, I have a Excel based spreadsheet file that does the calcs for you. You just plug in the variables like sprocket and wheel sizes, RPM etc, and it spits out the answers.

***Get YOUR official "Doc Locked, And Ready To Rock!" Stickers by clicking here!***
***Official Sprocket's Garage vinyl graphics and tees for sale HERE!***

Put down the wrench, and come out with your hands up!-Doc "Tranny Crusher" Sprocket, ATLTF Forum Admin, Thinkerer and Tinkerer, and all-around good dood. Wink

Gen. Mayhem- https://www.atltf.com/t2597-general-mayhem-race-tractor
MULE- https://www.atltf.com/t2153-lawn-boy-utltv
MULEII- https://www.atltf.com/t3328-1970-john-deere-112-the-beginnings-of-mule-ii
MULEIII https://www.atltf.com/t4263-mule3-brainstorming-ideas-etc#58287
Wrench, Wheel, Wreck, Repeat...

Subject: Re: speed calculation May 13th 2013, 12:04 am

Doc Sprocket wrote:: Thank you for posting this. Also, if this forum is capable of hosting the file and if anybody is interested, I have a Excel based spreadsheet file that does the calcs for you. You just plug in the variables like sprocket and wheel sizes, RPM etc, and it spits out the answers.

If you upload the spreadsheet onto a file hosting site and give me the download link, I can post it as a note on the Facebook page. All credit will go to you, of course.

Head Forum Administrator ** Chat Moderator ** Facebook Page Admin
ATLTF Facebook Page ** Chatbox ** How To Upload Pictures

_X_ FORUM ANNOUNCEMENTS _X_

Have a question? Ask me! Type in "@Doug" in your post!

Your ATLTF Staff:
Administrators: @Doug, @MightyRaze, @"Doc Sprocket", @Stretch44875
Moderators: @TheRainbowBoxer, @AllisKidD21, @Brianator, @RichieRichOverdrive

Subject: Re: speed calculation May 13th 2013, 8:41 pm

Okay- I'll see what I can do about hosting...

***Get YOUR official "Doc Locked, And Ready To Rock!" Stickers by clicking here!***
***Official Sprocket's Garage vinyl graphics and tees for sale HERE!***

Put down the wrench, and come out with your hands up!-Doc "Tranny Crusher" Sprocket, ATLTF Forum Admin, Thinkerer and Tinkerer, and all-around good dood. Wink

Gen. Mayhem- https://www.atltf.com/t2597-general-mayhem-race-tractor
MULE- https://www.atltf.com/t2153-lawn-boy-utltv
MULEII- https://www.atltf.com/t3328-1970-john-deere-112-the-beginnings-of-mule-ii
MULEIII https://www.atltf.com/t4263-mule3-brainstorming-ideas-etc#58287
Wrench, Wheel, Wreck, Repeat...

» Easy Belt Length Calculation: Pulley Swap Only
» CVT going to a 5 or 6 speed....For high speed tractors: Vario drive clutch, going to MST205 or 206
» tranny ? 5 speed or 6 speed
» Make a 12-Speed Transmission from a 6-Speed Transmission?
» Racing Lawn Tractor ( Mean Rabbit )