Thanks. Although I was wondering if it will help or hurt if I roll back. It might stop it from tipping back on a flat, but on a hill it would lift the tractor up so that when it tips back it just falls on me from up higher. I won't be trying any hill climbs with it anyway, so that shouldn't matter. I think it's high enough that it won't hit the ground going through ditches (hopefully).
Welded the tank brackets in. The straps will be bolted solid at the top with the adjusters at the bottom.
Tank is a real snug fit with the brackets welded in, but it fits. I dented in the right upper tube a little on the under side so I could tip the tank in easier. I also "adjusted" the left side of the tank. It's not really noticable. The circle drawn on is about where I'll put the filler neck and cap.
if that weren't the gas tank sitting in the basket, them tube poining out the back would be a perfect exhaust exit Dunno if I'd be comfortable running it through there with the gas tank sitting against it
'Course ya know, I'm gonna call it the "Pinto"
mr.modified Veteran Member
2015 Build-Off Top 3 Winner
2015 Build-Off Top 3 Winner
2016 Build-Off Top 3 Winner
2016 Build-Off Top 3 Winner
2018 Build-Off Finalist
2018 Build-Off Finalist
2022 Build-Off Entrant
2022 Build-Off Entrant
2500+ Posts
2500+ Posts!
1st Place Build-Off 2014
1st Place Build-Off Winner 2014
2023 Build-Off Entrant
2023 Build-Off Entrant
Age : 34 Join date : 2013-11-02 Points : 7169 Posts : 2910 Location : New Jersey USA
Yeah, I was thinking of possibly dumping the exhaust out back there too. I suppose, although probably unlikely, it could be a problem with a leak and perfect conditions. I think I might have it exit through a hole in the frame on the left side near the back of the running board but I'm not sure. It's going to be a tight fit with the dash and your legs on both sides of the frame. Not only that, but I want to stay away from the starter with the pipe so I can replace it if nessesary without removing the exhaust. Also, I'm still on the fence about using an alternator or not. If I do, it would have to go between the engine and the steering column. Still more work to do on other stuff though before we worry about it too much.
TheRainbowBoxer Moderator
1000+ Posts
1000+ Posts!
Age : 49 Join date : 2012-04-23 Points : 5701 Posts : 1091 Location : Galion, OH
When the exhaust goes that far, it'll probably be cool enough not to be a danger. Stretch's exhaust goes all the way out the back and even after a hard romp, the back end of it is cool to the touch.
Proud member of the Mower Cycle Gang... aka the "Mowrons!"
My build (Chaos is one of 3 built like this) Chaos Build
Welded in the pick up tube, vent tube, and filler neck from a 1990 or so buick century. I'm going to coat the inside with gas tank sealer to prevent rust. Maybe I should have cut the flange off of the filler neck, but I thought it would look or once It's painted. I guess we'll see.
Fairly small alternator from the same buick. This is about where it would go.
I need to put a v-belt pulley on the alternator. The pulley will sit out over the frame just a little, but I can put a guard to keep your foot from getting worn off.
Commandeered some headlights from a 60's plow jeep (Our own plow jeep). They look like sealed beams. Don't know if they work, didn't try them yet. If they are burned out, I'll have to see what it costs to get the sealed beams. It might be just as cheap to just buy some of the lights like I used on my simplicity. These lights are a little bigger. I would probably use these two in the middle, with two smaller ones on the outside of those. I guess I might as well put the alternator on. It's not really that heavy compared to everything else, and then I can use as many lights as I want without worrying.
Thanks. I made the battery hold down, coated the inside of the gas tank with sealer, and tested those headlights. Turns out the headlights work, so that will save a couple bucks at least. Too bad the lenses are a little different, someone must have replaced one at some point.
Thanks, I used a couple pieces of the original gas tank bracket from the engine for the battery hold down. Came out pretty good. Now I need to find a slotted bracket to hold the alternator so I can adjust the belt for it. I don't have a good way to cut slots in steel. I'm not sure it would come out too good with the torch.
Well thanks, I'll keep it in mind. But the other day I was thinking, the bottom wider bracket/bolt hole is mostly what holds the alternator straight. What if I just used an eyelet welded on the end of a threaded rod for adjustment instead of a slotted piece of metal. Sort of like what some of you guys make for clutch adjusters. (See nifty drawing below). What do you guys think? Either way, we have a couple junk cars here and there that I might be able to get something off of. I didn't look too hard yet. Also, the excess gas tank sealer was still slowly dripping out of the tank as of this morning (it's got a few years on it). Should be good by this weekend.
Subject: 
February 15th 2014, 8:06 pm
