|
| | belt issue again |  |
|
+2canadianromper Fattypipemuarry 6 posters | | Author | Message |
|---|
Fattypipemuarry
Member
Age : 29
Join date : 2011-06-02
Points : 5039
Posts : 62
Location : Russell County Kentucky
|  Subject: belt issue again  December 18th 2011, 11:00 pm | |
| alright i can get my belt to stay on with my clutch pushed in but it still pulls an my belt is crap | |
| | | | canadianromper
Member
Age : 25
Join date : 2011-11-30
Points : 4862
Posts : 114
Location : ontario canada
| | Subject: Re: belt issue again December 25th 2011, 10:02 pm | |
| im trying to figur that out too when i switch my pulles and what i am going to do is put some more idler pulleys in and thats it.but what i think u need is somthing that would go right beside the pulley like a bolt that would keep the belt from falling of when u push in on the clutch.thats my opinion and thats what i am going to do with my tractor so the belt dosen`t fall off in the middle of a deep mud hole. | |
| | | | dangeroustoys56
Veteran Member
Age : 54
Join date : 2010-02-10
Points : 7078
Posts : 1726
Location : Florida, USA
| | Subject: Re: belt issue again December 27th 2011, 5:45 am | |
| Belt retainers - also check to see if the belts are in line to the pulleys - my mod MTD had a tendency to eat belts - turns out the trans pulley was higher then the other drive pulley and it tore them up. | |
| | | | Fattypipemuarry
Member
Age : 29
Join date : 2011-06-02
Points : 5039
Posts : 62
Location : Russell County Kentucky
| | Subject: Re: belt issue again December 27th 2011, 3:49 pm | |
| it dont make sense cause it stays on with hte clutch pushed in why wont it without the clutch out | |
| | | | pullingtractorbuilder
New Member
Join date : 2013-02-28
Points : 4288
Posts : 3
| | Subject: Re: belt issue again February 28th 2013, 7:48 pm | |
| i need drive belts front(motor) and rear (trans) for a mtd. anyone got any? | |
| | | | Chopperhed
Moderator
Age : 58
Join date : 2012-10-14
Points : 5256
Posts : 801
Location : Edmonton, Alberta, Canada Eh!
| | Subject: Re: belt issue again February 28th 2013, 8:50 pm | |
| - Fattypipemuarry wrote:
- it dont make sense cause it stays on with hte clutch pushed in why wont it without the clutch out
Sounds like your pulleys may be out of alignment. | |
| | | | Hillbilly Homer
Member
Join date : 2012-04-22
Points : 4842
Posts : 197
Location :
| | Subject: Re: belt issue again March 28th 2013, 2:00 pm | |
| Check to see how much flex the transaxle pulley has. With the belt engaged it may be flexing and throwing it out of true. i had this happen with the stock pulley on my murray..  | |
| | | | Sponsored content
| | | | | | | belt issue again | |
|
Similar topics |  |
|
| | Permissions in this forum: | You cannot reply to topics in this forum
| |
| |
| | Who is online? | In total there are 17 users online :: 0 Registered, 0 Hidden and 17 Guests
None
Most users ever online was 412 on January 7th 2023, 7:59 am
|
|
