Moose's Diesel Massey

Looking great Moose! Pipes are going to set that thing apart from the crowd. I like the steering linkage. Excellent engineering there!   

Hellz yeah shes gonna sound and look good! I am anticipating what is gonna bend and break then I am overengineering for breakage so I dont have to mess with it again lol

Well guys my ***** dickered a target of oppertunity landed me a little Yanmar L70 for cheap so now the massey will be a diesel lol Never fear however I have a new project for the harley pipes so they wont be sitting around long!

Hey, good job getting it running! Now roll some coal!

Haha shes rocking and chooching so hard that the muffler rattled off the first time I got her going smoke was just blowing out the exhaust lol

Nice! How did you find this diesel? What machine are they usually packaged in?

I found it on ebay was a local so I called the guy up they are usually on pumps or generators have seen them on other stuff but I am not sure what else they come on lol

Cool little motor Moose! I still think the Massey wants to be a gasser though. We shall see where the Harley pipes end up!

the pipes are going to end up on the skid deere for a milsurp 4 banger should sound good too! but its a little bit in the future because of the massey eatting my time lol

Alrighty guys update time since it was like almost 60 degrees out I put myself through some pain and misery to get some pics for you ladies :p

Whats big and bad and yanmar all over?


That gal



She doesnt look to bad with the yanny in the engine spot is a pretty tight fit but not to bad



I straightened out the shifter as best I could with torch and pipe it doesnt look horrible and itll work so I am content





I may have to rethink the 10" pulley... Not! Ill just throw in a tensioner and a couple idlers



I bet stretch knows this position well... sitting where the seat will be and I can chill with my feet on the front wheels lol my boots block out the wheels...



The air cleaner will need to be reworked to fit better as it rubs against the hood atm even with the cover off so I will need to work on getting clearance for that



Little bit of room out front maybe a area for a horn or something more sinister...



Chugga chuggah choo choo!

I will more than likely add a stack and get rid of the muffler just so I have room for a battery for lights and a air compressor... why would I need a air compressor you might ask? aside from the obvious airing up tires? well if I can find a nice one I am gonna put a ye olde style train whistle on her! lol I am also debating fuel tank locations Id like to either put it under the seat where theres some extra room or Id like to put it in the front portion of the hood where there is a small space I am leaning more towards under the seat but that will be for another weekend...

Wow, looks sweet. Close to a test drive (nudge nudge) Can you play with the injection pump at all?

Yea, 10 might be a bit big... Looks good sitting on there.

Stretch44875 wrote:

Yea, 10 might be a bit big...  Looks good sitting on there.

Agreed^ lol I kinda think that you will experience more of a immediate "tug" of the belt with those pulleys instead of a nice slide into gear.

Ill look around at what I got and online see what I can see I kinda like the spoked look so Ill see if I can find a cast iron 6 or 8. The yanny is a 6 hp and doesnt actually like the 10 inch pulley from what I gathered test running it, took a little bit to spin up and stuff so not really into that kinda spooling up so Ill just have to go for the gear ratio and se if I can gear it down for the torque!

As for test drive... maybe in a month Ill set it out there so I dont rush I am taking it slow so I know I do everything right the first time I am trying to keep from half assing it

Not really a update just mounted the diesel that was about it. Working on calling in some favors to use a lathe and a tube bender maybe see if I can find a K&n filter so I can redo the intake so it takes up less room well see

Moose wrote:

Not really a update just mounted the diesel that was about it. Working on calling in some favors to use a lathe and a tube bender maybe see if I can find a K&n filter so I can redo the intake so it takes up less room well see

my autozone has some offbrand air filters that are chrome and look badass for like 12-13 bucks

Looking good moose... I'm gonna laugh if ya get stuck though... just so ya know... LOL If nothing else I'll bring the 18 hp to haspin lol

between the gearing the pulley ratio and the tires that are gonna be on it and my fat ass :p I seriously doubt she is gonna get stuck Ill briong the stuff I cant use and dont need maybe we can swap a bunch of stuff save on shipping lol

I really like it, it will be cool to see how the little diesel does, I also vote slightly smaller pulley

Alright so kinda a update I guess worked more on my tan than anything so I got some bushings for the front axle so that is all mounted up bought some split rims for the front so I could mount up the tires ordered bearings for said rims then did some other stuff... lol























oh yeah got the gas pedal cut welded and stuck on forgot to get a pic though lol by the end of the day I was so wore out I just wanted to sit back and relax got a lot done though Oh and I ordered a 7.25" pulley so it will be 1:1

Nice! No shortcuts, nice. cant wait to see some drivin!

sorta got a idea for the clutch so I am just waiting for the pulley to deal with the clutch found a old throttle cable Ill use for the foot throttle then all I gotta do is figure out a high low lever and she will be ready for a drive

Nice! I really like the massy look. Any way you can turn up the injection pump just for sh*ts and giggles?

redlinemotorsportts wrote:

Nice! I really like the massy look. Any way you can turn up the injection pump just for sh*ts and giggles?

ROLLIN COAL!!!  

heh I been tinkering but I dont wanna risk a runaway so I am taking it slow gotta wait for the exhaust before I can tune it anymore :p

Lookin good moose!