What have you done to your tractor today?

Didnt do anything to my tractor but did get another lol

105 Cub Cadet

God damnit Mike you gotta share with me bro lol.

Yea lol, Well i not the biggest fan of hydro cubs even tho there tons tougher then a mtd hydro but it was in the scrap yard readt for the crusher so i had to save her i paid for it weighed 650 pounds cost me $170 lol but couldnt see it get crushed, but find me a nice set of 4 bolt 4'' bolt wheels 10 x9.00 or 11 wide and you can have the rer massey lol.

Well today i done a tune up on my mud mower.
Also changed the oil the syntetic.
And i started on stack supports.

today i looked at my tractor amd thought what piece of junk and walked away begining my search for a new engine lol

gearheadmike wrote:

Kel that sux,but sweet pic of it lol

Well did nothing to any tractors 2day just took the sears for a ride in the nearby fields.

That thing looks pretty sweet! have you got a YouTube channel? I'd like to see more of that thing.

Remade battery box and added hood.

Well today i made a gas pedel limmiter.
And also fixed the throttal cabel.

Installed a chain protector under the jackshaft, added a push/pull main power switch, Installed Tunnel sheetmetal, started working on light mounts.

today i found an engine to try in my mtd. a 14hp briggs twin out of an 87 montgomery ward. hopefully tomorrow i can start tearing it down and clean the insides

i havent got to mod on my 90 murray in a few days due to rain and cold weather since i have no where indoors to work on it until next week but bought a 92 murray in mint mint condition running prefect and all from a guy that bought it new... gave $40 for it... cant believe it but gonna be able to do more to it since i have nearly nothing in it... starting on it in a couple hours

Well today i got a new belt and also installed it and then i fired it up a did a test drive.

I'm trying to find a ride so I can go pick up a tractor that 2 and a half hours away
I'm getting a 1970 dynamark

today i got my rear tires put on the rims for the lifted mower, still trying to find a starter, also considering paying $50 for a 16 hp kohler

put a gas pedel on it, wired up my kill swith and put the engine on

thought a bout the front end got some ideas, now need to go through with them,lol

Well today i rewelded on my hand lever and also fix my locking setup so i dont have to hold my hand lever.
Also whent on a ROMP.

Flushed the engine, added new oil, modified the dip stick with a bigger seal so now it's tight. And had a test run and a stress test for the engine. And done some anti-rust with acid threat ment.

Fabricated the skid plate for front and rear ends, modified brush guard from old 4 wheeler to fit the mower, painted everything and the cargo rack that'll be going on once finished...

Well today i made a linkage for the gov to replce the one i lost.

Tightened down the hitch properly, and flushed and drained the Jonsered / Craftsman for oil.

So lets hope I remember that it has no oil now

started the exhaust mod, got a few things cleaned up and prepped, mounted one of the two front wheels...

I put a bumper on the front it looks pretty sweet. But I locked up the trans axle from shifting from reverse to 1st gear. Now if only i could get the case open on it.

prometheusEDI wrote:

started the exhaust mod, got a few things cleaned up and prepped, mounted one of the two front wheels...

Woah woah are those front blaster tires? Haha, im running those on the rear of mine

Close! YFM-200 moto4 wheels all the way around

very nice. Those knobby's will sling a lot. Great choice of tractor to mod too, C-frames hold up great. Cant wait too see this done. Do you have any videos on it?